脊髓灰质炎病毒Ⅲ型Sabin株C抗原和D抗原的分离及特性分析

目的分离脊髓灰质炎病毒Ⅲ型Sabin株(sPVⅢ)C抗原和D抗原,并分析其部分特性。方法采用CsCl密度梯度离心法分离sPVⅢ的C抗原和D抗原,电镜观察病毒形态;SDS-PAGE检测病毒结构蛋白组成;微量BCA法检测蛋白浓度,计算每种抗原所占比例;细胞病变法检测病毒滴度。同时检测上样浓度及超离次数对C抗原纯度的影响。结果sPVⅢC抗原和D抗原在透射电镜下均呈球形,C抗原病毒颗粒密度较小,外壳大多较为松散,D抗原病毒颗粒密度较大,结构更稳固;C抗原由VP0、VP1、VP3蛋白组成,D抗原由VP1、VP2、VP3和VP4蛋白组成;C抗原和D抗原分别约占总蛋白含量的10%和90%,部分C抗原在分离前及分离过程中易产生聚集;D抗原的病毒滴度高于C抗原。降低上样浓度及进行二次超离可提高C抗原纯度。结论采用CsCl密度梯度离心法成功分离了sPVⅢ的C抗原和D抗原,C抗原滴度远低于D抗原,且部分易产生聚集,较难达到较高纯度。     

Biphenyl liquid crystal epoxy containing flexible chain: Synthesis and thermal properties

A biphenyl type liquid crystal epoxy (LCE) monomer 4,4′-di(2,3-epoxyhexyloxy)biphenyl (LCBP4) containing flexible chain was synthesized and the curing behavior was investigated using 4,4′-diaminodiphenylmethane (DDM) as the curing agent. The effect of curing condition on the formation of the liquid crystalline phase was examined. The cured samples show good mechanical properties and thermal stabilities. Moreover, the relationship between thermal conductivity and structure of liquid crystalline domain was also discussed. The samples show high thermal conductivity up to 0.28–0.31 W/(m*K), which is 1.5 times as high as that of conventional epoxy systems. In addition, thermal conductive filler, Al₂O₃, was introduced into LCBP4/DDM to obtain higher thermal conductive composites. When the content of Al₂O₃ was 80 wt%, the thermal conductivity of the composite reached to 1.86 W/(m*K), while that of diglycidyl ether of bisphenol A (Bis-A) epoxy resin/DDM/Al₂O₃ was 1.15 W/(m*K). Compared with Bis-A epoxy resin, the formation of liquid crystal domains in the cured LCE resin enhanced the thermal conductivity synergistically with the presence of Al₂O₃. Furthermore, the introduction of Al₂O₃ also slightly increased the thermal stabilities of the cured LCE.     

超滤-纳滤组合工艺对东太湖原水的处理效果

随着工业化进程的不断加快,东太湖水质日趋恶化,给常规处理增加了很大的处理难度。针对水源污染问题和给水深度处理的需要,开展了超滤-纳滤双膜组合工艺处理东太湖原水的中试研究,考察双膜工艺对出水水质的提升效果。结果表明,超滤-纳滤双膜工艺对水质常规指标具有较好的去除效果,CODMn和TOC的去除率分别为91.7%和90%;对荧光类物质的去除主要表现在对芳香族蛋白质、类富里酸物质、溶解性微生物代谢产物的去除;此外,双膜组合工艺对小分子二甲基异莰醇(2-MIB)和土臭素(GSM)的去除率分别为70%和77%,表明该工艺对水中主要致嗅物质具有良好的去除能力。     

浅析小型水电站厂用电节约的优化措施

水电站厂用电指标使用综合厂用率,反映电站厂用电消耗的实际情况,可通过厂用电率合理性分析电站厂用耗电情况以及节能降耗挖潜的空间,促进厂用电的合理管理,提高电站效益。文章结合华能甘肃水电开发有限公司管控的6座小型水电站厂用电管理实践,分析了影响水电厂用电损耗的相关因素,提出了厂用电节能降耗的应对措施。     

PVC地板行业研究现状及发展趋势

概述了国内外PVC地板行业的生产及应用现状,比较了几种地板材料的优缺点,介绍了PVC地板生产技术的研究进展情况,分析了国内PVC地板行业的发展趋势。     

铝空气电池用6061和7075铝合金阳极电化学性能

研究了工业6061铝合金（6061）、航空7075铝合金（7075）和纯铝作为铝空气电池阳极材料的电化学性能，分析其作为阳极的可行性及适用环境。进行了阻抗、极化曲线和恒电流放电实验并进行了表面表征，计算了在40～120mA/cm²电流密度下连续恒流放电的阳极能量密度。用电子探针显微镜（EPMA）对电极表面形貌进行了研究，用波谱分析仪（WDS）进行表面分析。研究结果表明，合金元素在电池放电过程中会改变阳极的表面特性。6061中合金元素含量对电池阳极材料的性能产生了积极影响，使得合金的表面放电面积变大，放电均匀，更适合作为铝空气电池阳极材料。     

石墨烯改性涂层防护性能研究

为减少团聚，提高石墨烯在涂层中的分散性，研究采用纳米分散技术预先制备了石墨烯分散液，再将其分散至环氧树脂中获得石墨烯改性复合涂层。通过对石墨烯含量为 0、0.3%、0.6%的复合涂层进行盐水浸泡、盐雾、阴极剥离实验及电化学性能测试，证明石墨烯的加入显著增强了涂层的防护性能。石墨烯复合涂层在 3.5%盐水中浸泡 1 008 h后，涂层低频阻抗仍大于 106 Ω·cm²比未添加石墨烯的涂层提高了 3个数量级，且盐雾实验 6 000 h后涂层表面仍保持完好；含 0.6%石墨烯，的涂层耐蚀行为劣于石墨烯含量为 0.3%的涂层。     

Removal of Cu2+ from Water Using Liquid-Liquid Microchannel Extraction

The very good extraction selectivity of Cu²⁺ from water was demonstrated with a new microchannel equipment, by employing di-(2-ethylhexyl)phosphoric acid (D2EHPA) as an extractant and kerosene as a solvent. The effects of different experimental parameters on the extraction efficiency E, the volumetric mass transfer coefficient K_La, and the entrainment were experimentally investigated. The results showed that the extraction efficiency increased with increasing temperature, extractant concentration, phase ratio (organic/aqueous), and pH. The total flow rate, phase ratio, and pH were found to have a great effect on the mass transfer, whereas the temperature and the extractant concentration showed little effect.     

氯化铵蒸发器结垢成分鉴别及原因分析

多效蒸发器结垢的问题常常发生,影响热效率和装置的正常运行。为明确导致蒸发器结垢的原因和成分,利用X射线衍射（XRD）、等离子发射光谱（ICP）、扫描电镜能谱（SEM-EDS）、偏光显微镜、拉曼光谱和离子色谱等分析测试技术,对浙江大洋生物科技集团股份有限公司的氯化铵多效蒸发器上的不明结垢物做了表征和分析。结果表明,该结垢物的主要成分为磷酸铁、氧化铝和有机物的混合物。探讨了发生上述结垢的原因,并提出相应的解决方案,减少了公司氯化铵蒸发器的结垢。     

Local body cooling to improve sleep quality and thermal comfort in a hot environment

The effects of local body cooling on thermal comfort and sleep quality in a hot environment were investigated in an experiment with 16 male subjects. Sleep quality was evaluated subjectively, using questionnaires completed in the morning, and objectively, by analysis of electroencephalogram (EEG) signals that were continuously monitored during the sleeping period. Compared with no cooling, the largest improvement in thermal comfort and sleep quality was observed when the back and head (neck) were both cooled at a room temperature of 32°C. Back cooling alone also improved thermal comfort and sleep quality, although the effects were less than when cooling both back and head (neck). Mean sleep efficiency was improved from 84.6% in the no cooling condition to 95.3% and 92.8%, respectively, in these conditions, indicating good sleep quality. Head (neck) cooling alone slightly improved thermal comfort and subjective sleep quality and increased Stage N3 sleep, but did not otherwise improve sleep quality. The results show that local cooling applied to large body sections (back and head) could effectively maintain good sleep and improve thermal comfort in a hot environment.